New Member 1994 Nitro Tracker Livescope

[marottadc]

Hello everyone! I am a new member to the forums! Last year I purchased a 1994 Nitro Tracker Fish and Ski with 115 Mercury 2-stroke. I have added beautiful LED deck lights (connected to that little light switch on the side of the gauge/steering wheel column), a stern and bow floodlight for docking at night or night time fishing, a Livescope and 2 Garmin 93SV units (one at the bow on the Livescope and one at the gauge cluster). Currently these are on a dedicated 100ah Amped Outdoors LiPo, but I just added two more 100ah Amped Outdoors LiPo's to the gas tank compartment at the stern, which I want to have run the 12/24v MotorGuide trolling motor and the graphs/Livescope (I talked to Garmin, they said it would be fine in regards to interference). I posted a new topic in the electronics section regarding an issue I am having wiring these new batteries into a 4 position switch. If anyone could help I would really appreciate it. I look forward to being a member of the community and contributing as much as I can!

 

[Runnin’BobR]

Welcome to the forum!

 

[Cyco]

Welcome

 

[NitroAdmin]

Welcome to the forum.

 

[Joe Winkler]

Hello everyone! I am a new member to the forums! Last year I purchased a 1994 Nitro Tracker Fish and Ski with 115 Mercury 2-stroke. I have added beautiful LED deck lights (connected to that little light switch on the side of the gauge/steering wheel column), a stern and bow floodlight for docking at night or night time fishing, a Livescope and 2 Garmin 93SV units (one at the bow on the Livescope and one at the gauge cluster). Currently these are on a dedicated 100ah Amped Outdoors LiPo, but I just added two more 100ah Amped Outdoors LiPo's to the gas tank compartment at the stern, which I want to have run the 12/24v MotorGuide trolling motor and the graphs/Livescope (I talked to Garmin, they said it would be fine in regards to interference). I posted a new topic in the electronics section regarding an issue I am having wiring these new batteries into a 4 position switch. If anyone could help I would really appreciate it. I look forward to being a member of the community and contributing as much as I can!

Are you talking about a battery kill switch, On/Off ? For your trolling motor? If you are then it's your positive battery cable you will run to the one side of the stop switch, and then take the same positive cable you cut off and hook the lead going up to your troller and hook it up to the other side of the on/off switch. Done deal. Be sure to install a on/off switch on your Black box hot wire also it don't draw its battery down when not in use.

 

[Joe Winkler]

Are you talking about a battery kill switch, On/Off ? For your trolling motor? If you are then it's your positive battery cable you will run to the one side of the stop switch, and then take the same positive cable you cut off and hook the lead going up to your troller and hook it up to the other side of the on/off switch. Done deal. Be sure to install a on/off switch on your Black box hot wire also it don't draw its battery down when not in use.

Do not even attempt to hook up your graphs to the same wires as the trolling motor. You will hate people to the point of mass murder everyone in your home town, you will hate your boat and probably kick your dog every time you see him. Power your graphs and black box off your single 100ah battery. I run 2- 9vs and 1- 106vs 2- black boxes 32lvs and a 34lvs off of 2-50ha lithium batterys wired to 24volt for 10 hours and they never get below 22volt. Garmins best friend is high voltage up to 32volts. Show quality screen clarity. And I kiss my dog and love my home town folks and I own the best old 2013- Z9 in the country.

 

[Chobeemauga]

Welcome to the site!

 

[Hooked03]

Hi, new member, thanks for the add! I purchased a 1990 Nitro 185. It’s in great shape but has a few issues to sort out. I’m trying to get a manual but Tracker boats says they don’t have one? I need to figure out what the four though holes on the stern are for. Which ones need to be plugged and type of plug. The bilge is filling up quickly so one or more needs plugged. I have a plug in the top one and the middle bottom one has a 1/2” PVC screw in plug. I figured the other two would be for the live wells. The live wells fill up slightly but not all the way. Any details on the through holes would be appreciated. Also, the engine (150 Johnson) ran well for about 1 hour but on the way back to the ramp, it started missing. Ran fine at low RPM but missed if you throttled. Filled up 87 oct. with 10% eth.

 

[Cyco]

Hi, new member, thanks for the add! I purchased a 1990 Nitro 185. It’s in great shape but has a few issues to sort out. I’m trying to get a manual but Tracker boats says they don’t have one? I need to figure out what the four though holes on the stern are for. Which ones need to be plugged and type of plug. The bilge is filling up quickly so one or more needs plugged. I have a plug in the top one and the middle bottom one has a 1/2” PVC screw in plug. I figured the other two would be for the live wells. The live wells fill up slightly but not all the way. Any details on the through holes would be appreciated. Also, the engine (150 Johnson) ran well for about 1 hour but on the way back to the ramp, it started missing. Ran fine at low RPM but missed if you throttled. Filled up 87 oct. with 10% eth.

You may have wanted to start a new post.

My opinion, I'd be running premium in those old motors, just my 2 cents.
The lowest one center, under the motor should be your bilge. The test are fot live well, bilge pump out, etc.


#admin

 

[Tymwaster]

Deathenol is just a bad idea - in the long run it's cheaper just to pony up for premium.