Search results

Ok, I have gps. I'm gonna by navionics chip for north region and also gonna buy hotspots map. I'll email you when I get the hotspots. It might be a little though. Gonna be there 7/4-7/11

Taking a vaction to The Turtle Flambeau Flowage in Wisconsin in July. Anyone ever fish there and have any pointers for me? Any info would be helpful. Thanks

Thanks airforce!! The recessed cup holder looks about right!!

I'm actually looking to replace the cup holder at the center console. Just below the gear shifter

Looking for a cup holder for my nitro. Cruise down the river, the wind must have caught it just right and it was gone. Didn't notice till I got back to the launch ramp. Anyone know where I could find one? Or do I have to just go through tracker?

Hi everyone. I have a 2009 90 hp mercury 2 stroke. While cruising wide open throttle at 5400 rpm, it'll all of sudden drop 10mph and drop to about 2000 rpm. And then after about 20 seconds it'll jump back up to 5400, and then after about 1 minute, it'll drop back down. I'm hoping it might be old...

Hi everyone, I'm going on a fishing trip in 2 weeks to table rock lake. I live in Illinois. I'm bringing my boat down. I had my bearings on my trailer replaced 2 years ago. I noticed today that they seem a little greasy on the outside. Their not throwing grease or covered in grease. Just a...

So the wife gave me the go ahead to buy a new steering system for the nitro. I currently have a very cranky rack and pinion. Besides hydraulic ( way out of my price range) I'de like to get something fairly easy to install myself and pretty good quality. I very tired of having fight to make a...

Thanks a lot!! Some really good info, and really like the diagrams. I'll give it a try. for th

I have greased the zerk. Do I keep pumping fresh grease until new grease pushes all old grease out? I also have to turn the steering wheel all the way out so the arm is fully out of the cylinder right? have

So my steering has recently became very stiff, mainly when turning one direction. It's not too bad when I'm on plane, but idling is a bit tough. I have the rack and pinion steering and I have a 2008 nitro 750 sc. I've been reading a lot online about taking cables loose and cleaning out all the...

Wayne, the humminbird 997 goes to the fuse panel, so not directly to the battery. The unit at the bow is not side imaging, only down imaging. The batteries are probably 4 years old. So they are definately due for replacing. I work construction so currently I'm out of work for a little while. So...

Everything else worked fine. Livewells, trolling motor, Humminbird at the bow. If it was the battery wouldnt they all have issues with power?

I'll take it out a couple of more times b4 i winterize it and see if it loosenes up. If it doesn't loosen, then i'll take it apart and see what is bent. Thanks for the help.

No the shaft doesn't appear bent. Hopefully it'll loosen up.

Is there a way to straighten the shaft out or buy just a new shaft? Or would i have too buy a whole new trolling motor?

Hell yea, I'm pumped

Cool, thanks for the info. I can barely wait for Saturday. Hoping the rain holds off, but temp looks like its gonna be nice. I bought the hotspots fishing maps, so I got some spots to try. Anyone got any "secret" spots that they would wanna share with a fellow fisherman. :D

Also Greg, do they just sell the mounting bracket for the XNT-9-DI-T? I already have that transducer. The bracket just broke, and I really don't want to buy a whole new transducer? Thanks again for your help.

Thanks for the info Greg. That would have really sucked if I damaged the unit. I will install the XNT-9-DI-T then. Is it easy to install to the quick release base? Just a matter of unplugging the old cable and plugging in the new one? Is there a plug on the cable that comes with the XNT-9-DI-T?